Synthesis and characterization of VO–vanillin complex immobilized on MCM-41 and its facile catalytic application in the sulfoxidation reaction,and synthesis of 2,3-dihydroquinazolin-4(1H)-ones and disulfides in green media

In this work, a vanillin complex is immobilized onto MCM-41 and characterized by FT-IR, X-ray diffraction, scanning electron microscopy, energy dispersive spectroscopy, thermogravimetric analysis, and BET techniques. This supported Schiff base complex was found to be an efficient and recoverable catalyst for the chemoselective oxidation of sulfides into sulfoxides and thiols into their corresponding disulfides (using hydrogen peroxide as a green oxidant) and also a suitable catalyst for the preparation of 2,3-dihydroquinazolin-4(1H)-one derivatives in water at 90°C. Using this protocol, we show that a variety of disulfides, sulfoxides, and 2,3-dihydroquinazolin-4(1H)-one derivatives can be synthesized in green conditions. The catalyst can be recovered and recycled for further reactions without appreciable loss of catalytic performance.     

Methyl orange degradation enhanced by hydrogen spillover onto platinum nanocatalyst surface

Following a thermal reduction method, platinum nanoparticles were synthesized and stabilized by polyvinylpyrrolidone. The colloidal platinum nanoparticles were stable for more than 3 months. The micrograph analysis unveiled that the colloidal platinum nanoparticles were well dispersed with an average size of 2.53 nm. The sol–gel‐based inverse micelle strategy was applied to synthesize mesoporous iron oxide material. The colloidal platinum nanoparticles were deposited on mesoporous iron oxide through the capillary inclusion method. The small‐angle X‐ray scattering analysis indicated that the dimension of platinum nanoparticles deposited on mesoporous iron oxide (Pt‐Fe₂O₃) was 2.64 nm. X‐ray photoelectron spectroscopy (XPS) data showed that the binding energy on Pt‐Fe₂O₃ surface decreased owing to mesoporous support–nanoparticle interaction. Both colloidal and deposited platinum nanocatalysts improved the degradation of methyl orange under reduction conditions. The activation energy on the deposited platinum nanocatalyst interface (2.66 kJ mol^?1) was significantly lowered compared with the one on the colloidal platinum nanocatalyst interface (40.63 ± 0.53 kJ mol^?1).     

General Formation of Macro-/Mesoporous Nanoshells from Interfacial Assembly of Irregular Mesostructured Nanounits

Mesoporous core–shell nanostructures with controllable ultra-large open channels in their nanoshells are of great interest. However, soft template-directed cooperative assembly to mesoporous nanoshells with highly accessible pores larger than 30 nm, or even above 50 nm into macroporous range, remains a significant challenge. Herein we report a general approach for precisely tailored coating of hierarchically macro-/mesoporous polymer and carbon shells, possessing highly accessible radial channels with extremely wide pore size distribution from ca. 10 nm to ca. 200 nm, on diverse functional materials. This strategy creates opportunities to tailor the interfacial assembly of irregular mesostructured nanounits on core materials and generate various core–shell nanomaterials with controllable pore architectures. The obtained Fe,N-doped macro-/mesoporous carbon nanoshells show enhanced electrochemical performance for the oxygen reduction reaction in alkaline condition.     

基于空气争化的介孔纳米TiO2的应用研究

本研究创建连续流动气相光催化实验系统,采用动态配气法生成一定低浓度的甲醛气体,开发利用介孔纳米TiO2为光催化材料,以促进利用光催化技术应用于消除室内有害污染气体更具实际意义和商业价值.研究表明,以非表面活性剂有机小分子三乙醇胺为模板剂制得了介孔TiO2材料,其粒径在20～30 nm之间;通过控制气流速度为7.5 cm/s以消除传质对反应的影响,在相对湿度为28%和反应温度为25℃的条件下,相对具有相近吸光性能和粒度的DegussaP25,介孔纳米TiO2具有更高的光催化降解甲醛的反应效率.     

Fine Dry Grinding of Zeolite in a Laboratory Ball Mill

This paper presents the importance and usage of natural zeolites, which was recently recognized in the industry. Therefore, the grinding properties of natural zeolite were studied with the emphasis on a kinetic study in a ball mill. The experimental mill employed was laboratory sized, 200 mm diameter, 191 mm length, providing a total mill volume of 6000 cm³, with a total mass of 5.62 kg of steel balls of 25 mm diameter with a charge of 20% of the mill volume and with a rotation speed of 76 rpm. The breakage parameters were determined by using single sized feed fractions of ?850+600 μm, ?600+425 μm, and ?425+300 μm for the zeolite samples. The S_i (specific rate of breakage) and B_{i, j} (primary breakage distribution) values were obtained for those feed size fractions in order to predict the product size distributions by simulation for comparison to the experimental data. From the experimental results, S_i values increased as the feed sizes became coarser, i.e., the highest S_i value was 0.85 min^?1 for ?850+600 μm, while the lowest S_i value was 0.65 min^?1 for ?425+300 μm feed ground in the mill. The B_{i, j} values obtained for the zeolite sample were γ=0.84, ?=0.61, and β=4.25. The breakage parameters obtained showed that the zeolite is broken faster than quartz and slower than calcite and barite in terms of the a_T values reported previously at the same experimental conditions. The simulations of the product size distributions of zeolite were in good agreement with the experimental data using a standard ball mill simulation program. The slowing‐down effect was also seen in the mill after 4 min. of grinding.     

Fabrication of Zeolite A Rods with Irregular Macropores by Self-assembly of Zeolite A Microcrystals Using Microwave-assisted Hydrothermal Synthesis

Zeolite A rods by self-assembly of zeolite A microcrystal were successfully synthesized by microwave-assisted hydrotherrnal synthesis. The average size of zeolite crystals consisting of self-assembling materials was about 300 nm and the length of zeolite rods was in the range of 15--30μm.     

Liquid phase oxidation of p-chlorotoluene to p-chlorobenzaldehyde over cobalt-doped mesoporous titania with a crystalline framework

Cobalt-doped mesoporous titania with a crystalline framework synthesized by surfactant templating method presented highly selective (99%) and reasonable conversion rate (49%) of catalytic oxidation of para-chlorotoluene to para-chlorobenzaldehyde in acetic acid using aqueous hydrogen peroxide as oxidant for the first time. Recycling of the catalyst indicates that the catalyst can be used a number of times without losing its activity to a greater extent. By contrast, cobalt-doped mesoporous titania without a crystalline structure and cobalt doped the commercial titania, Degussa P25 prepared by impregnation method with the similar concentration of cobalt were found inactive. The effects of catalyst concentration, reaction time, reaction temperature, and solvents on the performance of the catalyst were also investigated.     

Reactivities of tetraalkyltin complexes toward Pt/HY zeolite

Tetraalkyltin complexes, SnR₄ (R = Me, Et, Pr, Bu) could react with Pt/HY at 193, 243, 273 and 333 K, respectively. The reactions occurred on the surface of the zeolite and the organotin grafted zeolites were characterized in detail. The framework and the microporous structure of the grafted Pt/HY zeolites were retained. However, the modified zeolites showed better size selectivity in the absorption of hydrocarbons.     

Synthesis and adsorption properties of gold nanoparticles within pores of surface‐functional porous polymer microspheres

Mesoporous polymer microspheres with gold (Au) nanoparticles inside their pores were prepared considering their surface functionality and porosity. The Au/polymer composite microspheres prepared were characterized by transmission electron microscope (TEM), X‐ray diffraction (XRD), and Brunauer–Emmett–Teller (BET) techniques. The results showed that the adsorption of Au nanoparticles could be increased by imparting the pore structure and surface‐functional groups into the supporting polymer microspheres (in this study, poly (ethylene glycol dimethacrylate‐co‐acrylonitrile) and poly (EGDMA‐co‐AN) system). Above all, from this study, it was established that the porosity of the polymer microspheres is the most important factor that determines the distribution and adsorption amount of face‐centered cubic (fcc) Au nanoparticles in the final products. Our study showed that the continuous adsorption of Au nanoparticles with the aid of the large surface area and surface interaction sites formed more favorably the Au/polymer composite microspheres. The BET measurements of Au/poly(EGDMA‐co‐AN) composite microspheres reveals that the adsorption of Au nanoparticles into the pores kept the pore structure intact and made it more porous. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 5627–5635, 2004     

超稳Y沸石制备技术对沸石铝分布的影响 Ⅱ.均匀铝分布的超稳Y沸石的制备

对水热处理后得到的USY沸石作进一步的酸处理以及采用改进的氟硅酸盐溶液骨架富硅工艺,分别得到了经XPS剖面分析证实为铝分布均匀的超稳Y沸石HAY-Ⅰ和HAY-Ⅱ。IR分析表明,在酸处理过程中从USY沸石中去掉的那部分非骨架铝类与3690cm~(-1)处羟基有关,仍残留在HAY-Ⅰ沸石中的那部分非骨架铝类与3670cm~(-1)和3600cm~(-1)处羟基有关。XRD和化学分析表明HAY-Ⅰ沸石仍含有约50％的非骨架铝类,而HAY-Ⅱ沸石则基本上不含非骨架铝类,HAY-Ⅱ沸石还显示更高的结晶保留度。DTA分析表明,HAY-Ⅰ和HAY-Ⅱ两种沸石的热稳定性均高于USY沸石。